A Volvo truck has many systems that can be reset using special tools or reset sequences if they no longer work. Resettable systems include ABS, air dryer, automatic transmission, battery, brake pedal, check engine light, climate control module, EBS, ECU, hazard warning lights, radio, trouble codes and passwords.
Volvo Truck ABS Reset
The anti-lock braking system or ABS reduces your truck’s braking force to prevent the wheels from locking. To reset the ABS you must turn off the ABS light on the dashboard. You can do this by removing the cable that runs between the truck and the trailer. If the ABS lights are still on, press the brake pedal six times to reset the ABS sensor. After you have done this and the ABS lights are still not clear, walk past the light at the end of the trailer and see if there are any connections to the actual light itself as there may be broken wires. In rare cases, the above steps may not work. In this case there could be a problem with the ABS sensor or some wiring issues that are beyond your repair skills. It is better to contact your auto mechanic for further repairs. Wait for a prompt to appear. It contains the warning if you understand the implications of the reset. Because resetting the air dryer system is irreversible and can further damage your vehicle, you cannot drive it unless the air dryer components have been repaired or replaced.
Resetting the Volvo truck automatic transmission
To give your truck a driving force, the automatic transmission performs. If you drive a Volvo truck, especially older models, you may find that it won’t shift into neutral even if you’ve already turned the switch off. If this is the case, resetting will help. To reset the automatic transmission, disconnect the batteries from it and turn on the switch and key. This step will allow you to dump the remaining energy in the shifter or gearbox RAM. If you try and it doesn’t work, there may be a mechanical problem in the gearbox.
Volvo Truck Battery Reset
After replacing the battery in your Volvo truck, it is imperative to perform the battery reset customization to erase the values from the previous battery. This allows the vehicle’s charging strategy to be reset to a new, fresh battery. You need advanced iSCAN SF Volvo software to reset the battery. It will communicate the process quickly. Start diagnostics. When diagnosing, make sure you connect your truck to an appropriate power supply. Select the appropriate buttons that appear on the screen. It usually refers to the make or makes of your truck. Then select the service function key. After that, you need to select the specific model of your vehicle from the options presented there. When you’re done, select Enter and then Fast Service. It would be helpful if you tap on the central electronics module or reset the CEM battery to zero. A warning message will appear before proceeding. Just click Enter when you’re done. The reset process will now start. Be sure to check and clear each trouble code so the new battery can start over.
Volvo Truck Brake Pedal Reset
When you replace your brake pads, you will find that your brake pedal sometimes becomes a bit stiff. Brake Pedal Reset allows you to release the brake pedal on your truck’s central computer. To reset the brake pedal, you should first disconnect the battery cable from your truck. Then press the brake pedal until you have completely drained your vehicle’s electrical system. With no power stored it is easier for your truck to fully reset its computer system. You will then see the indicator lights come on.
Resetting the Volvo Truck Check Engine Light
The check engine light notifies you when there is a problem with the engine or other parts. It also shows if there are any error codes present in the electronic control unit or ECU of your Volvo truck. Because the control unit stores all codes in its memory, you may need to reset your truck’s check engine light after it has been repaired or serviced. It’s so easy and quick to do. First you need to open the fuse box cover. You can find it under the steering wheel. Then plug the electrical connector into the diagnostic device. Get into your Volvo Truck and turn the ignition key. Make sure it is in position II. After that, you will see a blinking light on the diagnostic tool. Wait for it to stop. The codes on your truck ecu will be cleared as the check engine light has already been reset.
Volvo Truck Climate Control Module or AC Reset
If you are having problems with your Volvo Truck’s air conditioning or climate control module, the best way to get it working properly again is to reset it. Before reversing, make sure you close the doors, hood, hood or other openings. Then switch the ignition to position II. After closing the windows, hold the driver and passenger window switches in the driver’s door panel in the closed position for about five to eight seconds. Then release the buttons and remove the ignition key. You have to operate the remote control twice by locking and unlocking it. After that, switch the heater from off to high and back off again.
Volvo Truck EBS Reset
The electronic braking system or EBS of your Volvo truck is responsible for maintaining stable steering, especially during emergency braking or when driving on slippery roads. So it is always important to keep it in good condition. If resetting the EBS is the remaining solution to fix your truck, you can quickly do it yourself. Turn off your truck first and then step on the brake pedal. Do not release the brake within 10 seconds. Turn on your truck and release the brake pedal. You should see an error code after following the procedure. If not, you can repeat the steps until it works.
Volvo Truck ECU or Computer Reset
The ECU records your truck’s engine performance. Therefore, all the controls you make are saved whenever you use them. If your truck has been repaired or serviced you should reset the ECU to clear it from the values and fault codes. To reset the ECU, disconnect your truck from the battery. Turn on the ignition key for 15 minutes. Besides disconnecting the battery, you can also try resetting the ECU using other recommended reset tools.
Reset Volvo Truck Trouble Code
The Trouble Codes help you to identify the problems present in your truck. If you need to reset your vehicle’s system, the fault codes should also be cleared. To perform the reset you need to make sure your truck is stationary. Check the displayed air pressure. It should only be at least 10 bars. If not, start the engine and fill the air system. You have to turn off the ignition. This will reset the controller. Then start the engine without depressing the foot brake. After waiting about five seconds, slowly depress the foot brake. Make sure it’s fully depressed by holding the footbrake for about seven seconds. Slowly release the foot brake and turn off the ignition. Wait a few seconds again before turning on the ignition. Then check the error codes.
Resetting the hazard lights for Volvo Trucks
Resetting the hazard lights is one of the easiest tasks because you don’t need any equipment. But of course only do this if your truck has been driven for a service or repair. To reset, after turning on the ignition, you will see a warning message on your truck’s dashboard. Eliminate it first and then enter the service mode. Press and hold the service button for about five seconds. A prompt will appear on the screen. Press the select button. The blue box on the screen indicates that you are already in service mode. Press the select button again to go to the next service. Then press the down arrow button to confirm the reset.
Reset Volvo truck password
If you want to change or reset your password in your Volvo truck, you can do it in the app. Simply navigate to the \”More\” tab on the application screen, then select \”Account\” and \”Manage Account\”. Wait a few seconds You will be redirected to the website. You will be asked to enter your ID and password. Just follow the next few steps and you’re good to go.
Volvo Truck Radio Reset
To reset the radio on your Volvo truck, turn the key to accessory mode while turning off the exterior and interior lights and air conditioning. Make sure the radio has enough power to see an off sign. Leave your truck for about two to three hours. You will then see the off sign on the radio change to code. Once it is displayed, enter the code that you receive by first contacting Volvo Customer Service.
Best Volvo Truck Reset Tool
To reset your Volvo truck system, you need a reliable reset tool. You can use OTR reset tool that works in Volvo and Mack trucks. It’s easy to use. All you have to do is plug it into your truck and the diagnostics will start running. You can complete the entire reset process in five minutes or less.
If you need Volvo Heavy Duty Truck Scanner, please vivit www.obd2tool.com .